Lumac Inc
Previous Page Listing ID#: 170044

Auction Location

Ford City, PA 16226
Auction Dates and TimesSALE IS COMPLETED
Wednesday Jan 22, 2020 Completed
Auction Type
 Live Auction 
Company Information
Hartland Auctioneers

Contact: Dean A. Gearhart GPPA
Phone: (724) 368-9788
Email: info@hartlandmachinery.com
Website: www.hartlandauctions.com

GoToAuction.com ID#: 6269
View company information and listings

Free Email Notifications

Sign up for the GoToAuction.com email notifications and we will let you know about sales in your area!  You may set up alerts by area (zip and radius), keywords, and by company.  It is FREE and only takes a few seconds to sign up.

Listing Terms and Conditions
No Merchandise may be removed until complete settlement has been made. 1.All purchases shall be paid for in full on the day of the sale, unless a wire transfer is required. The wire transfer shall be sent no later than the next business day by 3:00 PM. 2.Purchases shall be paid for with cash, WV, PA or Ohio co. checks, credit card or wire transfer. Any other state checks will require bank letter of credit. Invoices up to $10,000.00 may be paid for with a company check. Invoices above $10,000.00 shall be paid for with a wire transfer. 3.All items are sold as is where is and how is, with no warranties of any type expressed or implied concerning the merchandise being sold. Once an item is called Sold, it becomes the sole responsibility of the buyer. 4.Descriptions of merchandise contained in the catalog are intended for general information purposes only. Please examine items carefully before bidding as no refunds will be given. 5.A Buyer’s Premium of 12% applies to all lots sold in-house, 15% online. 3% surcharge for credit cards 6.$5 minimum bid. 7.No one under the age of 18 years of age is permitted to register or bid. 8.A properly stamped invoice, authenticated by our cashier, will be required by our check-out personnel in order that you may remove the items. Any discrepancies must be brought to our attention prior to removal from the property. 9.The auctioneers may remove items from the sale at their discretion. 10.The auctioneer is the sole authority on any disputed bid, and his word is final. We reserve the right to correct any clerical errors and to re-invoice if necessary. If a dispute arises out of this contract that cannot be settled through negotiation or mediation, any-and-all court proceeding shall take place in Butler, Pa.16101. 11.All machines are either disconnected at the plug or at the quick disconnect box, box not included. 12.Removal dates and times: After the end of the auction until 5:00 pm. Weekdays from 9 am to 4 pm, for dates to be announced by auctioneer. All other dates by appointment only. Call auctioneer to schedule. Items not picked up will be considered abandoned, unless prior arrangements have been made with the auctioneer. Storage fees will apply for items picked up after three weeks. Call or see auctioneer for details. Additional $150 per day fee for checkout on the day you pick up. 13.NSF or stop payment checks are subject to a $35.00 returned check fee
Listing Information

Lumac Inc

2021 PA-66, Ford City, PA 16226

Wednesday, January 22, 2020 Doors open at 8 am, auction begins at 10 am

Preview: Tuesday, January 21, 2020 from 9 am to 3 pm

Directions: From Pittsburgh, take PA-28 N toward Etna, take the US-422 E/PA-28 N exit toward Kittanning/Indiana, take exit A for PA-66 S toward Ford City, follow for approximately 5.5 miles, destination on the right.

TERMS: Items sold as is, where is, how is. An 12% buyer’s premium applies to all lots sold. Accepted payments include credit card (with 3% surcharge fee), cash, company check (PA, OH, or WV checks), bank letter of credit with out-of-state checks, or wire transfer.

 

IMPORTANT INFORMATION: THE AUCTIONEER MAKES NO WARRANTY OR GUARANTEE, EXPRESSED OR IMPLIED, AS TO THE ACCURACY OF THE INFORMATION HEREIN CONTAINED. IT IS FOR THIS REASON THAT BUYERS SHOULD INSPECT ALL ITEMS PRIOR TO BIDDING. THE BROCHURE IS INTENDED TO PROVIDE GENERAL INFORMATION OF THE EQUIPMENT BEING OFFERED AND IS SUBJECT TO ERRORS, OMISSIONS, ADDITIONS OR DELETIONS. COMPETE AUCTION CATALOGS WILL BE AVAILABLE THE DAY OF THE AUCTION. ITEMS OFFERED MAY OR MAY NOT NECESSARILY BE SOLD AS DESCRIBED AND/OR PHOTOGRAPHED.

 

Horizontal Boring Mills

Lucas Precision 5” spindle, horz table type boring mill, 10-1220 RPM spindle speed, 48”X86” working table size, partial pendant control, power draw bar, with Trak 103 2-axis DRO, built in outrigger supports, morse taper Travels- 60” vertical, 48” X 90” , SN 42B3714

Lucas Precision 642B-144 6” spindle, horz table type boring mill, 60”X158” table, NUM CNC control, 50 taper, power draw bar, built in outrigger supports, table way covers, Travels-36” spindle,  96” vertical, 90”x13’, SN 42B 4416

Lucas 542B-60, 5” spindle, horz table type boring mill, 8-1200 RPM spindle speed, 48”X98” table, morse taper, partial pendant control, Travels- 50” vertical, 72”X96”, SN 42B 1304

Lucas 542B,  horz floor type boring mill, 78”x292” table, partial pendant control, morse taper, Trak 2-axis DRO, Travels- 7’ vertical, 36” spindle, SN 2206 

CNC Lathes & lathes

Mazak Power Master X 160, 34” swing over ways, 22” swing over cross slide, 160” length, equipped with Mazatrol T Plus control, 31” 3- jaw chuck, 8” & 18” steady rests,  front 8-position turret, back 4-position turret, chip pan & conveyor, SN 122871

Mazak Quick Turn Smart 250, with 10” 3-jaw chuck, tool setter, 10 position turret, chip conveyor, Mazatrol Smart controls, SN 252278, Mfg 12/13

Mazak Quick Turn 35N Univ., with 12” 3-jaw chuck, tool setter, 12 position turret, chip conveyor, Mazatrol T32-2 controls, SN 110448

 

LeBlond 40” standard, 46” x21’, 4.5-500 RPM spindle speed, 3” spindle bore, 32” swing over cross slide, equipped with hardened way strips, quick change tool post, Trak 3-axis DRO, 10” 18” & 30” steady rests, 21” 3-jaw chuck, 24” 4- jaw chuck, 2 way rapid, thread dial, SN NK 1045

LeBlond Heavy Duty, 22”x70”, 12-528 RPM spindle speed, 2” spindle bore, 15” swing over cross slide, equipped with Aloris quick change tool post, 12” 4- jaw chuck, chip pan, thead dial

 

CNC & manual mills

Mazak Mazatech V-655B, with Mazatrol M32B control, 25-5/8” x68-1/2” table, 50 taper, 30 ATC, SN 104808

Mazak VTC-16B, with Mazatrol PC-fusion CNC 640M control, 16”x57.5” table, 40 taper, 24 ATC, SN 142419

Zayer 77AF horz mill, pendant control, 27.5”x85” table, 33-2150 RPM spindle speed, Pathfinder 3-axis DRO, all angle head, Travels- 30” vertical, 27”x72”

Van Norman 24LA horz mill, 12”x50” table, 2-1400 RPM spindle speed, with right angle head, 29” head travel, 30” table travel, SN 3060-1263

Bridgeport Series II vertical mill, with Series I two HP head, 11”x58” table, SINO 2-axis DRO, X-axis power feed, SN 2320S

Bridgeport variable speed head vertical mill, 9”x42” table, SN 171434

Fabricating Equipment

Scotchman iron worker model 12012, SN 50425M394

H-frame press, 50” between columns, 42” under ram

DoAll hydraulic surface grinder, 8”x24” permanent magnetic chuck

Pratt & Whitney 12” vertical shaper model B M-1513,, 24” rotary table, SN 436

DoAll metal master vertical band saw, 16” throat, 10” under guide, 24”x24” table, with blade welder

16” disc sander

37-5/8”x50” t-slotted table with tilt & slide’

48”x96” layout table

2” belt sander

Forklifts

Linde model H 100, diesel, double mast, 10,000 pound capacity,  128” lift, solid tire, SN 3185700004

Caterpillar T40B, LP, triple mast, side shift, 4000 pound capacity, 156” lift, SN 86 W 499

Clark C500YS-80, LP, double mast, 8500 poound capacity, 122” lift, solid tire, SN V68500567410

6000 lb boom

 

Welders

Miller Dimension 652 onboom cart with Lincoln LN-7 wire feed, SN KF948189, Stock no 903379

Miller Goldstar 400ss, SN JB478401

Lincoln Idealarc CV-400, with LN-7 wire feed, SN AC-676990, code 9303-M

Lincoln Square Wave TIG 275, with Magnum control, SN U1980315481, code 10523

Lincoln Power Mig 255, SN U1040417805, code 10990, K# K1693-1

Lincoln Power Mig 180 dual power, SN M3140108370, code 11828

Lincoln Idealarc TM 400/400, SN AC-283510, code 6785-c

Miller SR-300WRLA, SN K187577, 60% duty cycle

Lincoln Miniflex fume extractor

 

 

Compressors

Atlas Copco GA22Plus, 132 psi, 460v, SN API321874

Kaeser KRD 250 refirgerated air dryer

Jobsmart 10 gallon 25 psi portable

Twistair model TA0240BAA2AE, Shop # 136278, 110 psi,

Inspection tooling

Micrometers- outside- two sets 6”-12”, 24-30”, inside mics up to 107”, 80” Vernier caliper, Starrett dial height gage, gage blocks, roughness surface blocks, etcher, Platco 36”x48”x7” ledged granite surface plate,

Tooling – drills, end mills, taps, taper tooling,

 

 

ALSO

Angle plates-106”x84”x37”, 28.5”x27.5”x14”, 15”x30”x48”, 60”x62”x38”, 28”x22”x13”, 48”x48”x30” and more

Two t-slotted set up blocks 24”x60”x15”

Bott/Kennedy 6-drawer tool cabinet

Kurt vises

48” t-slotted rotary table, 1 degree increments

Lucas air operated 36”x48”x9.5” rotary table

YEW type 3086 X-Y recorder

Jenny combination cleaner model 753-C

Lanair MX300 waste oil heater

Heated parts cleaner, with agitation, 32“x 48” openings

Master 135,000 btu torpedo heater

Wagner paint pump

Crane test gauge

Beaver Model A threader

Rolling stairs

Fans

Pedestal grinders

Darex drill sharpeners

Dump hoppers

Famco #4C arbor press


Auction License: AU-002918-L
Photo Gallery

Save Listing As Favorite

Print Listing information

Share This Listing

  • Facebook
  • Email this Listing to a Friend






Sponsored Links

Lumac Inc

Hartland Auctioneers

Hartland Auctioneers


Contact: Dean A. Gearhart GPPA
Phone: (724) 368-9788
Sale Location
2021 PA-66
Ford City, PA 16226
Sale Dates and Times
Wednesday Jan 22, 2020 Completed
Sale Terms and Conditions
No Merchandise may be removed until complete settlement has been made. 1.All purchases shall be paid for in full on the day of the sale, unless a wire transfer is required. The wire transfer shall be sent no later than the next business day by 3:00 PM. 2.Purchases shall be paid for with cash, WV, PA or Ohio co. checks, credit card or wire transfer. Any other state checks will require bank letter of credit. Invoices up to $10,000.00 may be paid for with a company check. Invoices above $10,000.00 shall be paid for with a wire transfer. 3.All items are sold as is where is and how is, with no warranties of any type expressed or implied concerning the merchandise being sold. Once an item is called Sold, it becomes the sole responsibility of the buyer. 4.Descriptions of merchandise contained in the catalog are intended for general information purposes only. Please examine items carefully before bidding as no refunds will be given. 5.A Buyer’s Premium of 12% applies to all lots sold in-house, 15% online. 3% surcharge for credit cards 6.$5 minimum bid. 7.No one under the age of 18 years of age is permitted to register or bid. 8.A properly stamped invoice, authenticated by our cashier, will be required by our check-out personnel in order that you may remove the items. Any discrepancies must be brought to our attention prior to removal from the property. 9.The auctioneers may remove items from the sale at their discretion. 10.The auctioneer is the sole authority on any disputed bid, and his word is final. We reserve the right to correct any clerical errors and to re-invoice if necessary. If a dispute arises out of this contract that cannot be settled through negotiation or mediation, any-and-all court proceeding shall take place in Butler, Pa.16101. 11.All machines are either disconnected at the plug or at the quick disconnect box, box not included. 12.Removal dates and times: After the end of the auction until 5:00 pm. Weekdays from 9 am to 4 pm, for dates to be announced by auctioneer. All other dates by appointment only. Call auctioneer to schedule. Items not picked up will be considered abandoned, unless prior arrangements have been made with the auctioneer. Storage fees will apply for items picked up after three weeks. Call or see auctioneer for details. Additional $150 per day fee for checkout on the day you pick up. 13.NSF or stop payment checks are subject to a $35.00 returned check fee
Listing Details

Lumac Inc

2021 PA-66, Ford City, PA 16226

Wednesday, January 22, 2020 Doors open at 8 am, auction begins at 10 am

Preview: Tuesday, January 21, 2020 from 9 am to 3 pm

Directions: From Pittsburgh, take PA-28 N toward Etna, take the US-422 E/PA-28 N exit toward Kittanning/Indiana, take exit A for PA-66 S toward Ford City, follow for approximately 5.5 miles, destination on the right.

TERMS: Items sold as is, where is, how is. An 12% buyer’s premium applies to all lots sold. Accepted payments include credit card (with 3% surcharge fee), cash, company check (PA, OH, or WV checks), bank letter of credit with out-of-state checks, or wire transfer.

 

IMPORTANT INFORMATION: THE AUCTIONEER MAKES NO WARRANTY OR GUARANTEE, EXPRESSED OR IMPLIED, AS TO THE ACCURACY OF THE INFORMATION HEREIN CONTAINED. IT IS FOR THIS REASON THAT BUYERS SHOULD INSPECT ALL ITEMS PRIOR TO BIDDING. THE BROCHURE IS INTENDED TO PROVIDE GENERAL INFORMATION OF THE EQUIPMENT BEING OFFERED AND IS SUBJECT TO ERRORS, OMISSIONS, ADDITIONS OR DELETIONS. COMPETE AUCTION CATALOGS WILL BE AVAILABLE THE DAY OF THE AUCTION. ITEMS OFFERED MAY OR MAY NOT NECESSARILY BE SOLD AS DESCRIBED AND/OR PHOTOGRAPHED.

 

Horizontal Boring Mills

Lucas Precision 5” spindle, horz table type boring mill, 10-1220 RPM spindle speed, 48”X86” working table size, partial pendant control, power draw bar, with Trak 103 2-axis DRO, built in outrigger supports, morse taper Travels- 60” vertical, 48” X 90” , SN 42B3714

Lucas Precision 642B-144 6” spindle, horz table type boring mill, 60”X158” table, NUM CNC control, 50 taper, power draw bar, built in outrigger supports, table way covers, Travels-36” spindle,  96” vertical, 90”x13’, SN 42B 4416

Lucas 542B-60, 5” spindle, horz table type boring mill, 8-1200 RPM spindle speed, 48”X98” table, morse taper, partial pendant control, Travels- 50” vertical, 72”X96”, SN 42B 1304

Lucas 542B,  horz floor type boring mill, 78”x292” table, partial pendant control, morse taper, Trak 2-axis DRO, Travels- 7’ vertical, 36” spindle, SN 2206 

CNC Lathes & lathes

Mazak Power Master X 160, 34” swing over ways, 22” swing over cross slide, 160” length, equipped with Mazatrol T Plus control, 31” 3- jaw chuck, 8” & 18” steady rests,  front 8-position turret, back 4-position turret, chip pan & conveyor, SN 122871

Mazak Quick Turn Smart 250, with 10” 3-jaw chuck, tool setter, 10 position turret, chip conveyor, Mazatrol Smart controls, SN 252278, Mfg 12/13

Mazak Quick Turn 35N Univ., with 12” 3-jaw chuck, tool setter, 12 position turret, chip conveyor, Mazatrol T32-2 controls, SN 110448

 

LeBlond 40” standard, 46” x21’, 4.5-500 RPM spindle speed, 3” spindle bore, 32” swing over cross slide, equipped with hardened way strips, quick change tool post, Trak 3-axis DRO, 10” 18” & 30” steady rests, 21” 3-jaw chuck, 24” 4- jaw chuck, 2 way rapid, thread dial, SN NK 1045

LeBlond Heavy Duty, 22”x70”, 12-528 RPM spindle speed, 2” spindle bore, 15” swing over cross slide, equipped with Aloris quick change tool post, 12” 4- jaw chuck, chip pan, thead dial

 

CNC & manual mills

Mazak Mazatech V-655B, with Mazatrol M32B control, 25-5/8” x68-1/2” table, 50 taper, 30 ATC, SN 104808

Mazak VTC-16B, with Mazatrol PC-fusion CNC 640M control, 16”x57.5” table, 40 taper, 24 ATC, SN 142419

Zayer 77AF horz mill, pendant control, 27.5”x85” table, 33-2150 RPM spindle speed, Pathfinder 3-axis DRO, all angle head, Travels- 30” vertical, 27”x72”

Van Norman 24LA horz mill, 12”x50” table, 2-1400 RPM spindle speed, with right angle head, 29” head travel, 30” table travel, SN 3060-1263

Bridgeport Series II vertical mill, with Series I two HP head, 11”x58” table, SINO 2-axis DRO, X-axis power feed, SN 2320S

Bridgeport variable speed head vertical mill, 9”x42” table, SN 171434

Fabricating Equipment

Scotchman iron worker model 12012, SN 50425M394

H-frame press, 50” between columns, 42” under ram

DoAll hydraulic surface grinder, 8”x24” permanent magnetic chuck

Pratt & Whitney 12” vertical shaper model B M-1513,, 24” rotary table, SN 436

DoAll metal master vertical band saw, 16” throat, 10” under guide, 24”x24” table, with blade welder

16” disc sander

37-5/8”x50” t-slotted table with tilt & slide’

48”x96” layout table

2” belt sander

Forklifts

Linde model H 100, diesel, double mast, 10,000 pound capacity,  128” lift, solid tire, SN 3185700004

Caterpillar T40B, LP, triple mast, side shift, 4000 pound capacity, 156” lift, SN 86 W 499

Clark C500YS-80, LP, double mast, 8500 poound capacity, 122” lift, solid tire, SN V68500567410

6000 lb boom

 

Welders

Miller Dimension 652 onboom cart with Lincoln LN-7 wire feed, SN KF948189, Stock no 903379

Miller Goldstar 400ss, SN JB478401

Lincoln Idealarc CV-400, with LN-7 wire feed, SN AC-676990, code 9303-M

Lincoln Square Wave TIG 275, with Magnum control, SN U1980315481, code 10523

Lincoln Power Mig 255, SN U1040417805, code 10990, K# K1693-1

Lincoln Power Mig 180 dual power, SN M3140108370, code 11828

Lincoln Idealarc TM 400/400, SN AC-283510, code 6785-c

Miller SR-300WRLA, SN K187577, 60% duty cycle

Lincoln Miniflex fume extractor

 

 

Compressors

Atlas Copco GA22Plus, 132 psi, 460v, SN API321874

Kaeser KRD 250 refirgerated air dryer

Jobsmart 10 gallon 25 psi portable

Twistair model TA0240BAA2AE, Shop # 136278, 110 psi,

Inspection tooling

Micrometers- outside- two sets 6”-12”, 24-30”, inside mics up to 107”, 80” Vernier caliper, Starrett dial height gage, gage blocks, roughness surface blocks, etcher, Platco 36”x48”x7” ledged granite surface plate,

Tooling – drills, end mills, taps, taper tooling,

 

 

ALSO

Angle plates-106”x84”x37”, 28.5”x27.5”x14”, 15”x30”x48”, 60”x62”x38”, 28”x22”x13”, 48”x48”x30” and more

Two t-slotted set up blocks 24”x60”x15”

Bott/Kennedy 6-drawer tool cabinet

Kurt vises

48” t-slotted rotary table, 1 degree increments

Lucas air operated 36”x48”x9.5” rotary table

YEW type 3086 X-Y recorder

Jenny combination cleaner model 753-C

Lanair MX300 waste oil heater

Heated parts cleaner, with agitation, 32“x 48” openings

Master 135,000 btu torpedo heater

Wagner paint pump

Crane test gauge

Beaver Model A threader

Rolling stairs

Fans

Pedestal grinders

Darex drill sharpeners

Dump hoppers

Famco #4C arbor press

Gallery Images Loading, Please Wait...
  • Home
  • Hire an Auction Company
  • Add Your Auction Company
  • Member Login
  • Contact Us
  • Desktop Site
Return
Lumac Inc
 Live Auction
 
Auction Date(s)
Wednesday Jan 22, 2020 Completed
Auction Location

Ford City, PA 16226
Company
Hartland Auctioneers

Contact: Dean A. Gearhart GPPA
Phone: (724) 368-9788
Website: www.hartlandauctions.com

Listing Terms and Conditions
No Merchandise may be removed until complete settlement has been made. 1.All purchases shall be paid for in full on the day of the sale, unless a wire transfer is required. The wire transfer shall be sent no later than the next business day by 3:00 PM. 2.Purchases shall be paid for with cash, WV, PA or Ohio co. checks, credit card or wire transfer. Any other state checks will require bank letter of credit. Invoices up to $10,000.00 may be paid for with a company check. Invoices above $10,000.00 shall be paid for with a wire transfer. 3.All items are sold as is where is and how is, with no warranties of any type expressed or implied concerning the merchandise being sold. Once an item is called Sold, it becomes the sole responsibility of the buyer. 4.Descriptions of merchandise contained in the catalog are intended for general information purposes only. Please examine items carefully before bidding as no refunds will be given. 5.A Buyer’s Premium of 12% applies to all lots sold in-house, 15% online. 3% surcharge for credit cards 6.$5 minimum bid. 7.No one under the age of 18 years of age is permitted to register or bid. 8.A properly stamped invoice, authenticated by our cashier, will be required by our check-out personnel in order that you may remove the items. Any discrepancies must be brought to our attention prior to removal from the property. 9.The auctioneers may remove items from the sale at their discretion. 10.The auctioneer is the sole authority on any disputed bid, and his word is final. We reserve the right to correct any clerical errors and to re-invoice if necessary. If a dispute arises out of this contract that cannot be settled through negotiation or mediation, any-and-all court proceeding shall take place in Butler, Pa.16101. 11.All machines are either disconnected at the plug or at the quick disconnect box, box not included. 12.Removal dates and times: After the end of the auction until 5:00 pm. Weekdays from 9 am to 4 pm, for dates to be announced by auctioneer. All other dates by appointment only. Call auctioneer to schedule. Items not picked up will be considered abandoned, unless prior arrangements have been made with the auctioneer. Storage fees will apply for items picked up after three weeks. Call or see auctioneer for details. Additional $150 per day fee for checkout on the day you pick up. 13.NSF or stop payment checks are subject to a $35.00 returned check fee

Lumac Inc

2021 PA-66, Ford City, PA 16226

Wednesday, January 22, 2020 Doors open at 8 am, auction begins at 10 am

Preview: Tuesday, January 21, 2020 from 9 am to 3 pm

Directions: From Pittsburgh, take PA-28 N toward Etna, take the US-422 E/PA-28 N exit toward Kittanning/Indiana, take exit A for PA-66 S toward Ford City, follow for approximately 5.5 miles, destination on the right.

TERMS: Items sold as is, where is, how is. An 12% buyer’s premium applies to all lots sold. Accepted payments include credit card (with 3% surcharge fee), cash, company check (PA, OH, or WV checks), bank letter of credit with out-of-state checks, or wire transfer.

 

IMPORTANT INFORMATION: THE AUCTIONEER MAKES NO WARRANTY OR GUARANTEE, EXPRESSED OR IMPLIED, AS TO THE ACCURACY OF THE INFORMATION HEREIN CONTAINED. IT IS FOR THIS REASON THAT BUYERS SHOULD INSPECT ALL ITEMS PRIOR TO BIDDING. THE BROCHURE IS INTENDED TO PROVIDE GENERAL INFORMATION OF THE EQUIPMENT BEING OFFERED AND IS SUBJECT TO ERRORS, OMISSIONS, ADDITIONS OR DELETIONS. COMPETE AUCTION CATALOGS WILL BE AVAILABLE THE DAY OF THE AUCTION. ITEMS OFFERED MAY OR MAY NOT NECESSARILY BE SOLD AS DESCRIBED AND/OR PHOTOGRAPHED.

 

Horizontal Boring Mills

Lucas Precision 5” spindle, horz table type boring mill, 10-1220 RPM spindle speed, 48”X86” working table size, partial pendant control, power draw bar, with Trak 103 2-axis DRO, built in outrigger supports, morse taper Travels- 60” vertical, 48” X 90” , SN 42B3714

Lucas Precision 642B-144 6” spindle, horz table type boring mill, 60”X158” table, NUM CNC control, 50 taper, power draw bar, built in outrigger supports, table way covers, Travels-36” spindle,  96” vertical, 90”x13’, SN 42B 4416

Lucas 542B-60, 5” spindle, horz table type boring mill, 8-1200 RPM spindle speed, 48”X98” table, morse taper, partial pendant control, Travels- 50” vertical, 72”X96”, SN 42B 1304

Lucas 542B,  horz floor type boring mill, 78”x292” table, partial pendant control, morse taper, Trak 2-axis DRO, Travels- 7’ vertical, 36” spindle, SN 2206 

CNC Lathes & lathes

Mazak Power Master X 160, 34” swing over ways, 22” swing over cross slide, 160” length, equipped with Mazatrol T Plus control, 31” 3- jaw chuck, 8” & 18” steady rests,  front 8-position turret, back 4-position turret, chip pan & conveyor, SN 122871

Mazak Quick Turn Smart 250, with 10” 3-jaw chuck, tool setter, 10 position turret, chip conveyor, Mazatrol Smart controls, SN 252278, Mfg 12/13

Mazak Quick Turn 35N Univ., with 12” 3-jaw chuck, tool setter, 12 position turret, chip conveyor, Mazatrol T32-2 controls, SN 110448

 

LeBlond 40” standard, 46” x21’, 4.5-500 RPM spindle speed, 3” spindle bore, 32” swing over cross slide, equipped with hardened way strips, quick change tool post, Trak 3-axis DRO, 10” 18” & 30” steady rests, 21” 3-jaw chuck, 24” 4- jaw chuck, 2 way rapid, thread dial, SN NK 1045

LeBlond Heavy Duty, 22”x70”, 12-528 RPM spindle speed, 2” spindle bore, 15” swing over cross slide, equipped with Aloris quick change tool post, 12” 4- jaw chuck, chip pan, thead dial

 

CNC & manual mills

Mazak Mazatech V-655B, with Mazatrol M32B control, 25-5/8” x68-1/2” table, 50 taper, 30 ATC, SN 104808

Mazak VTC-16B, with Mazatrol PC-fusion CNC 640M control, 16”x57.5” table, 40 taper, 24 ATC, SN 142419

Zayer 77AF horz mill, pendant control, 27.5”x85” table, 33-2150 RPM spindle speed, Pathfinder 3-axis DRO, all angle head, Travels- 30” vertical, 27”x72”

Van Norman 24LA horz mill, 12”x50” table, 2-1400 RPM spindle speed, with right angle head, 29” head travel, 30” table travel, SN 3060-1263

Bridgeport Series II vertical mill, with Series I two HP head, 11”x58” table, SINO 2-axis DRO, X-axis power feed, SN 2320S

Bridgeport variable speed head vertical mill, 9”x42” table, SN 171434

Fabricating Equipment

Scotchman iron worker model 12012, SN 50425M394

H-frame press, 50” between columns, 42” under ram

DoAll hydraulic surface grinder, 8”x24” permanent magnetic chuck

Pratt & Whitney 12” vertical shaper model B M-1513,, 24” rotary table, SN 436

DoAll metal master vertical band saw, 16” throat, 10” under guide, 24”x24” table, with blade welder

16” disc sander

37-5/8”x50” t-slotted table with tilt & slide’

48”x96” layout table

2” belt sander

Forklifts

Linde model H 100, diesel, double mast, 10,000 pound capacity,  128” lift, solid tire, SN 3185700004

Caterpillar T40B, LP, triple mast, side shift, 4000 pound capacity, 156” lift, SN 86 W 499

Clark C500YS-80, LP, double mast, 8500 poound capacity, 122” lift, solid tire, SN V68500567410

6000 lb boom

 

Welders

Miller Dimension 652 onboom cart with Lincoln LN-7 wire feed, SN KF948189, Stock no 903379

Miller Goldstar 400ss, SN JB478401

Lincoln Idealarc CV-400, with LN-7 wire feed, SN AC-676990, code 9303-M

Lincoln Square Wave TIG 275, with Magnum control, SN U1980315481, code 10523

Lincoln Power Mig 255, SN U1040417805, code 10990, K# K1693-1

Lincoln Power Mig 180 dual power, SN M3140108370, code 11828

Lincoln Idealarc TM 400/400, SN AC-283510, code 6785-c

Miller SR-300WRLA, SN K187577, 60% duty cycle

Lincoln Miniflex fume extractor

 

 

Compressors

Atlas Copco GA22Plus, 132 psi, 460v, SN API321874

Kaeser KRD 250 refirgerated air dryer

Jobsmart 10 gallon 25 psi portable

Twistair model TA0240BAA2AE, Shop # 136278, 110 psi,

Inspection tooling

Micrometers- outside- two sets 6”-12”, 24-30”, inside mics up to 107”, 80” Vernier caliper, Starrett dial height gage, gage blocks, roughness surface blocks, etcher, Platco 36”x48”x7” ledged granite surface plate,

Tooling – drills, end mills, taps, taper tooling,

 

 

ALSO

Angle plates-106”x84”x37”, 28.5”x27.5”x14”, 15”x30”x48”, 60”x62”x38”, 28”x22”x13”, 48”x48”x30” and more

Two t-slotted set up blocks 24”x60”x15”

Bott/Kennedy 6-drawer tool cabinet

Kurt vises

48” t-slotted rotary table, 1 degree increments

Lucas air operated 36”x48”x9.5” rotary table

YEW type 3086 X-Y recorder

Jenny combination cleaner model 753-C

Lanair MX300 waste oil heater

Heated parts cleaner, with agitation, 32“x 48” openings

Master 135,000 btu torpedo heater

Wagner paint pump

Crane test gauge

Beaver Model A threader

Rolling stairs

Fans

Pedestal grinders

Darex drill sharpeners

Dump hoppers

Famco #4C arbor press